Loading page content, please wait...Loading page content, please wait...Loading page content, please wait...Loading page content, please wait...
Talk with a technical expert.
Genuine Victron · North American 120V
The exact 2-meter North American AC power cord for compatible Victron Smart IP43 chargers with an IEC C14 inlet.
Victron Smart IP43 chargers use a separately ordered country-specific mains cord. The genuine ADA010100400 cord provides the correct NEMA 5-15P wall plug for standard North American 120V outlets, an IEC C13 charger-side connector, and 2 meters of practical reach for a clean, dependable charger installation.
Complete your Smart IP43 installation with the correct regional mains cord.
Victron supplies Smart IP43 chargers with a universal IEC C14 AC inlet so installers can choose the correct wall plug for their country. The ADA010100400 is the North American cord option, combining a grounded NEMA 5-15P wall plug with the matching IEC C13 connector used at the charger.
This is an AC mains accessory—not a battery charging lead. It carries wall power from a properly protected 120V outlet to the charger, which then converts that AC power into the controlled DC charging profile required by the connected battery bank.
NEMA 5-15P is the familiar grounded three-prong plug used with standard 120V household, garage, workshop, campground, and protected shore-power receptacles across the United States and Canada.
The IEC C13 charger-side connector mates with the IEC C14 inlet used by compatible Smart IP43 chargers. The charger's supplied retainer clip can help prevent accidental disconnection at the inlet.
At approximately 6.56 feet long, the cord provides practical reach for chargers mounted on nearby walls, electrical boards, equipment cabinets, and protected marine or RV utility spaces.
Victron separates country-specific AC cords from the charger so each installation can use the correct regional wall plug. This part is the North American 120V option.
Using the exact Victron accessory avoids uncertainty about plug format, grounding, connector fit, cord length, and compatibility with the charger-side retaining arrangement.
Use it as the required initial mains cord or as an exact-part-number replacement for a damaged, missing, or misplaced ADA010100400 cord.
Verify the charger inlet and part number before ordering.
Current Victron documentation lists ADA010100400 as the NEMA 5-15P, 2-meter mains cord for Smart IP43 chargers. The compatible charger uses an IEC C14 inlet, and the cord terminates in the corresponding IEC C13 female connector.
Some reseller catalogs also associate this cord with compatible Skylla-S chargers. Because charger generations and inlet configurations can differ, confirm the exact Skylla-S model and AC inlet before purchase rather than assuming universal fitment.
North American Smart IP43 charger installations.
Exact part number, length, plug type, charger connection, and compatibility.
Use a grounded, correctly protected outlet in a dry installation.
Pair this mains cord with a compatible Victron Smart IP43 charger.
The ADA010100400 supplies AC input power to the charger; it does not replace the charger, DC battery cables, overcurrent protection, or battery-specific charging configuration. Confirm the charger model, battery voltage, charge settings, AC circuit, and DC installation before commissioning.
Common questions about plug type, charger compatibility, voltage, length, and installation.
Yes, if your Victron Smart IP43 charger was supplied without a country-specific AC cord. Victron uses a separate mains-cord system so buyers can select the correct wall plug for their region. ADA010100400 is the 2-meter NEMA 5-15P option for North American 120V outlets.
Yes. The wall-side connector is a grounded NEMA 5-15P plug, the standard three-prong plug used with common 120V receptacles in the United States and Canada. The outlet and branch circuit must be correctly wired, grounded, and suitable for the connected charger load.
The charger-side connector is an IEC 60320 C13 female connector that mates with the IEC C14 inlet used on compatible Smart IP43 chargers. The charger includes a retainer clip that can help secure the cord at the inlet.
A generic IEC C13 cord may physically fit, but its conductor size, current rating, approvals, grounding condition, connector quality, and retainer compatibility may be unknown. Using the genuine Victron ADA010100400 removes that uncertainty and provides the correct North American plug and 2-meter length for the intended charger application.
No. The NEMA 5-15P plug is intended for standard North American 120V circuits. Although many Smart IP43 chargers accept a wide AC input range, this specific cord should not be adapted for a 240V receptacle. Use the correct Victron regional or voltage-specific mains cord instead.
It is intended for Smart IP43 chargers that use the matching IEC C14 AC inlet. Verify the charger model, inlet, label, and Victron documentation before ordering. The current Smart IP43 charger documentation lists the NEMA 5-15P cord as a separately ordered US plug option.
Some reseller catalogs describe ADA010100400 for Smart IP43 and compatible Skylla-S chargers, but current Victron catalog language specifically lists it for Smart IP43 chargers. Confirm the exact Skylla-S model and its AC inlet before purchase rather than assuming universal compatibility.
The cord is 2 meters long, which is approximately 6.56 feet. That provides practical reach from a wall outlet to a charger mounted on a nearby wall, cabinet, equipment board, or protected utility space.
No formal outdoor or waterproof rating is published for this accessory. Use it only in a dry, protected installation with a properly grounded outlet. The compatible Smart IP43 charger also requires a protected, ventilated location; its connection area is not waterproof.
