Loading page content, please wait...Loading page content, please wait...Loading page content, please wait...Loading page content, please wait...
Talk with a technical expert.
Genuine Victron long-range data cable
A 90-degree VE.Direct cable with the maximum supported direct-run length for distant RV, marine, and off-grid components.
The Victron VE.Direct cable 10m right angle is a genuine Victron Energy data cable for installations that need both approximately 33 feet of reach and a low-profile connection. Part ASS030531320 combines one right-angle VE.Direct connector with one straight connector, helping link supported SmartShunts, BMV monitors, MPPT controllers, chargers, inverters, and GX devices across large compartments without crushing a straight cable behind a shallow panel.
Reduce connector depth and mechanical stress when a straight cable would project too far from the device.
Shallow RV walls, marine helms, battery cabinets, and compact electrical boards can force a straight data cable into a sharp bend. The right-angle end routes the cable close to the device surface, reducing required rear clearance and helping protect the cable and VE.Direct port from constant pressure.
One end uses Victron’s low-profile right-angle VE.Direct connector. Place it at the device with the tightest clearance and route the wire along a protected surface rather than forcing a straight connector against a panel.
Reducing sharp bends and side-load can lower mechanical stress on the molded connector and device port. Add strain relief and test the connector orientation before permanently mounting the Cerbo GX, MPPT, SmartShunt, or other component.
Approximately 32.81 feet for components mounted in distant RV, marine, and off-grid compartments.
Route from a SmartShunt or MPPT in an RV basement to a GX device in the living cabin, from a marine battery compartment or engine room to a distant helm, or across a larger off-grid equipment area without field-spliced extensions.
Ten meters is Victron’s maximum supported direct VE.Direct run. Use the factory cable as one uninterrupted path, add strain relief, and keep the unshielded, untwisted data cable separated from high-current AC/DC wiring, motors, and other interference sources where practical.
Confirm a VE.Direct port on both devices before ordering.
Exact part-number matching and factory termination for professional installations.
Test the right-angle orientation and plan the full 10-meter route before mounting your equipment.
Exact part identification, connector configuration, compatibility, and installation limits.
VE.Direct, VE.Bus, VE.Can, RJ12, and USB interfaces are different cable families.
Match the cable to the labels and connector shape on both devices. A physically similar communication cable may use a different connector, pinout, or protocol. Review both product manuals when designing a Victron or Epoch-integrated system.
Choose the shortest factory cable that fits the route and connector-clearance needs.
Common questions about connector orientation, compatibility, signal reliability, and maximum-length routing.
Ten meters is the maximum direct VE.Direct cable length supported by Victron. This genuine factory cable is intended for compatible point-to-point VE.Direct connections at that distance. Reliable operation still depends on correct device compatibility, undamaged connectors, proper routing, and avoiding extensions or splices.
No. Victron part ASS030531320 has one standard straight VE.Direct connector and one right-angle connector. Use the angled end at the device with the tightest rear or side clearance.
Victron does not identify the cable as directional. In normal point-to-point VE.Direct use, place the right-angle end where clearance is tightest and the straight end where more space is available. Confirm the molded cable-exit direction before permanently mounting the device.
The right-angle design minimizes required depth behind mounting panels, but adjacent-port clearance depends on the exact device, connector orientation, and mounting position. Test-fit the connector and verify neighboring VE.Direct, USB, HDMI, power, and mounting access before final installation.
VE.Direct is Victron’s smaller four-core data connection for supported battery monitors, MPPT solar chargers, Orion XS units, Smart IP43 chargers, and certain VE.Direct inverters. VE.Bus and VE.Can use RJ45-style network cables for different product families, including MultiPlus or Quattro systems and CAN networks. These cable families are not interchangeable.
No, not as a universal battery communication cable. Epoch batteries with native Victron or CANbus communication normally require the battery model’s specified CAN-BMS cable or harness connected to a VE.Can or BMS-Can port. This product is for devices that actually provide VE.Direct ports.
It can connect compatible products equipped with VE.Direct ports. Common examples include supported BMV battery monitors, SmartShunts, BlueSolar or SmartSolar MPPT controllers, Orion XS units, Smart IP43 chargers, certain VE.Direct inverters, and compatible GX devices. Verify the port and manual for both products before ordering.
No. Victron states that VE.Direct cables cannot be extended. Do not cut, splice, daisy-chain, or add an inline extension. If more than 10 meters is required, use a VE.Direct-to-USB interface with an appropriate active USB extension as described by Victron.
Do not shorten the cable by cutting it. Route the factory cable with gentle bends and secure any extra length in a loose service loop away from sharp edges, heat, moving parts, water, and high-current conductors. Avoid tightly coiling or crushing the cable behind a panel.
Victron currently provides a standard five-year warranty on its power-product range, subject to its warranty terms and original-dealer support process. Keep your proof of purchase and contact the selling dealer for warranty assistance.
